Call Us Today! 0116 2799083 | Next Day Delivery on Orders Before 4pm|Sales@InStyleLED.co.uk
12 Watt CCT LED Tape (colour-temperature changing)2018-09-12T11:43:29+00:00

12 Watt CCT LED Tape

3014 SMD, 60 dual-white LEDs / metre
Commercial Grade

Availability: In Stock for next day delivery

InStyle’s dual-white 12-watt LED strip lights use the same high-quality Epistar 3014 paired LEDs as our high-power 24W dual-white LED tapes, but with only half the LEDs mounted per metre (60 diodes p.m., not 120 p.m.). So they draw only half the power. Use 12W dual-white LEDs for feature-lighting and highlights, and the brighter 24W LEDs for task-lights and main room lighting.

12-watt dual-white lighting is a colour-temperature changing (CCT) LED tape. InStyle’s CCT LEDs use commercial-grade SMDs, each of which houses both a warm-white and a pure-white chip for superior colour mixing. By adjusting their light mix, your LEDs can create any shade of white light.

With 60 dual-white 3014 LEDs per metre, this colour-temp changing tape draws 12 watts per metre with 50,000 hours of continuous-use life.

To learn more about CCT LED tapes, see our inVyci dual-white CCT LED control-system page.

Tape cut points are every 125mm – and InStyle offer a cutting and soldering service, so we’ll make up your order to the exact lengths your project needs, no matter the size. This LED tape is also available in waterproof versions (IP65- or IP67-rated), so it can be installed externally, or in bathrooms and other wet locations. InStyle’s water-resistant LED tape is sealed with a heatshrink coating, which not only protects against moisture but also makes cleaning easier.

  • Commercial Grade LED Tape
  • High Quality Branded LED Chip
  • Thick 2oz PCB board for maximum heat dispersion
  • High grade, long lasting resistors to stop LED chip damage
  • Premium white coating for  protection of the PCB board and to stop short circuiting
  • Smooth linear effect
  • IP65 splashproof & IP67 waterproof available
  • Product Codes:
    WWW-12 (CCT LEDs) / WWW-12-65 (CCT LEDs splashproof)
Product12 Watt CCT LED tape
LED Wattage:12 watts per metre
Voltage:24 volts
Colours:Any white shade can be created
CRI:85+
IP RatingNo coating or
IP65/IP67 heatshrink
LED Chip3014 SMD
LED Life70,000 hours
No. of LEDs:60 LEDs per metre (dual-white SMDs)
Lumens:1,250 per metre (max brightness)
Beam Angle:120 degrees
Cut Points:125 mm
Reel Lengths5 metres
Tape width:10 mm
Tape Height3 mm

 

Product Codes:
WWW-12 (CCT LEDs) / WWW-12-65 (CCT LEDs splashproof)

12 Watt CCT LED Tape Datasheet PDF

FAQs

InStyle LED manufacture and supply commercial-grade LED strip lights – which means our products are high quality and built to last, using only premium components and branded LEDs:

  • Brighter LEDs
  • Vibrant and consistent colours
  • Accurate life expectancy
  • Sturdy PCBs
  • Excellent resistor management

Find out more on our ‘commercial-grade LED’ support page.

Our CCT tapes and compatible controllers are sold separately.

The acronym CCT stands for Correlated Colour Temperature dimming & control.

To work out what transformer you require this is quite simple. Just take the amount of LED tape you have (in metres) and multiply this by the wattage of the LED tape you are using (per metre again).

For example 9m of 24w LED tape: 9 x 24w = 216w Therefore you would require a 240w transformer.

For more information, see our support page on LED power supplies and their output.

For this type of LED tape you will require just a transformer to get this working. You connect the starter lead coming out of one end. This is then wired to the transformer, red wire goes to the + terminal and the pure-white & warm-white wires both go to the -ve terminal. The cable can be extended as required, if you need to mount the transformer further away.

For more information and advice, see our support page on how to connect your LED power supply.

IP67-rated LED tapes (heatshrink coated) are required in areas where you will need resistance to water. For example bathrooms, kitchens and exterior. The heatshrink version is waterproof but it cannot be submersed, for example in a pond. InStyle’s IP67 heatshrink is a protective coating over the LED tape, this makes it easy to wipe to clean etc.

For more information, see our support page describing the waterproof LED strip light options we offer.

All of our LED strips are cuttable. Each can be cut at various points, either 50mm,100mm,150mm or 200mm depending on whitch wattage version you have. We can either cut the lengths to your specific lengths as required or you can do this yourself. Once cut to length to join this to a transformer or another piece you will need to be capable of soldering, or if not we also supply 2 types of clips. One type is a starter lead clip, which is s clip that joins onto the off cut and has a cable coming out of it. The other clip is a ‘tape to tape clip’, this clip joins 2 pieces together.

For more information, see these links offering advice and support on cutting and soldering your LED tape, or using clip-on connectors to extend your tape’s length.

LED strips are designed to be very flexible. Their PCBs (printed circuit boards) are so robust that many LED tape products can be bent up to 90 degrees with no difficulty.

Be aware that higher-power LED strips are less flexible than lower-power ones. This is because the LED modules are placed closer together on high-power strips, and require wider PCBs (for more heat dispersal).

For more info and examples, check out our support page.

 

This product is inVyci compatible

Premium-brand customers supplied by InStyle LED

cert

You may also be interested in the following product(s)

LED light strip

10-Watt RGBW LED Tape

Outputting up to 665 lumens per metre of LED tape, these 10-watt RGBW LED strip lights produce an ideal level of illumination for highlights and other decorative lighting applications.

15w RGB LED strip

15-Watt RGB LED Tape

With twice the output of 7.5w tapes, our 15-watt RGB LED tape is ideal for areas where more brightness is required or where there is a lot of strong ambient lighting. 60 branded 5050 tri-SMDs per metre.

LED light strip

20-Watt RGBW LED Tape

With four colours in each SMD, 20-watt RGBW LED tape mixes light at source for smooth consistent lighting. It will produce up to 1330 lumens per metre when all four colours are at full brightness.

10w white LED lights - 12 volt LED strip lights

10-Watt White LED Tape

With 120 LEDs per metre, each one a branded 3528 SMD, our 10-watt white LED tape draws 9.6 watts to give up to 720 lumens per metre.

12 Watt CCT LED Tape Customer Reviews