12 Watt RGB + Dual-White
LED Tape

5-in-1 SMD, 30 LEDs Per Metre
Commercial Grade

Availability: In Stock for next day delivery

A 5-channel LED tape combining RGB and CCT light palettes, our 12-watt RGB + dual-white strip-lights offer the ultimate in colour control. Every metre of flexible PCB mounts 30 x 5050 SMDs – each housing five coloured LED chips (red, green, blue, warm-white & pure-white). This arrangement not only allows full RGB brightness and colour adjustment, it also provides smooth colour-temperature control from ~3000K to ~6000K white light.

And using RGB and dual-white light in tandem opens up an unlimited range of pastel colours that three primary colours (RGB) couldn’t create on their own.

With brightness up to 864 lumens per metre, InStyle’s high-quality 12W RGB + dual-white LED tape lights provide plenty of light for highlights, accents and other features. If you need even brighter illumination, check out our 24W RGB + dual-white LED tape.

RGB + dual-white LED tape is available on 5m standard reels with cut-points every 100mm or InStyle can pre-cut and solder your LED tape order to the lengths you need. There’s no minimum order, and we can offer helpful advice and technical support to make your LED project run smoothly from start to finish.

  • Commercial Grade LED Tape
  • High Quality Branded LED Chip
  • 5-channel 5050 SMDs – red / blue / green / warm-white / pure-white
  • Thick 3oz PCB board for maximum heat dispersion
  • High grade, long lasting resistors to stop LED chip damage
  • Premium white coating for  protection of the PCB board and to stop short circuiting
  • Smooth linear effect
  • IP65 splashproof & IP67 waterproof available
  • Product Codes: RGB-CCT-12 / RGB-CCT-12-65 (splashproof)
Product12 Watt RGB / dual-white LED tape
LED Wattage:12 watts per metre
Voltage:12 volts
Colours:RGB + 2x dedicated white (warm 3000K & pure 6000K) LEDs
IP RatingNo coating or
IP65/IP67 heatshrink
LED Chip5050 SMD 5 in one
LED Life50,000 Hours
No. of LEDs:30 LEDs per Metre
Lumens:864 lm/m (maximum output)
Beam Angle:120 degrees
Cut Points:100mm
Reel Lengths5 Metres
Tape width:10mm
Tape Height3mm

Product Codes:
RGB-CCT-12 / RGB-CCT-12-65 (splashproof)

Fully compatible with these LED controllers

5-colour multizone remote controller for compound dual-white+RGB LEDs

5-colour wall-mounted controller for compound dual-white+RGB LEDs

12 Watt RGB+CCT LED Tape Datasheet PDF

12 Watt RGB+CCTLED Tape Datasheet PDF


RGB + Dual-White LEDs offer the colour-mixing of 3-colour RGB (red/blue/green) plus dual-white (warm & pure shades) light palettes, all combined in a single diode. Together they provide ultimate flexibility for white and coloured lighting.

LED strips are designed to be very flexible. Their PCBs (printed circuit boards) are so robust that many LED tape products can be bent up to 90 degrees with no difficulty.

Be aware that higher-power LED strips are less flexible than lower-power ones. This is because the LED modules are placed closer together on high-power strips, and require wider PCBs (for more heat dispersal).

For more info and examples, check out our support page.

To work out what transformer you require this is quite simple. You take the amount of LED tape you have in metres and x this by the wattage of the LED tape you have, again per metre.

For example 16m of 12w LED tape: 16 x 12w = 192w. Therefore you would require a 200w transformer.

For more information, see our support page on LED power supplies and their output.

This type of LED tape requires an LED transformer and LED receiver to get it working. Connect the transformer to the receiver – this supplies power to the circuit. Because RGB + dual-white LED control requires five channels, use a length of 5-core cable to connect the receiver and LED tape: black lead goes to +ve and the five coloured leads are wired to -ve. The cable can be extended as necessary, to mount the transformer as far away as required.

For more information, choose one of these links for support and advice on how to install either simple or larger LED tape projects.

Deciding on which wattage you require is all down to what kind of application you are fitting the LED tape in.

12w RGB + dual-white LEDs are ideal to be used as feature lighting. Lighting to highlight areas, as a secondary lighting. Ideal for covings, drop down ceilings signage etc. to give a smooth halo effect. The 10w would be preferred to the 5w for these applications if there is a high amount of ambient lighting.

24w RGB + dual-white LEDs are ideal to be used as general lighting or as feature lighting for areas larger than covings etc. For example washing down front bars / back bars / under kitchen cabinet lighting as ‘working light’

For more information, see our support page discussing how bright your LED tape needs to be.

InStyle LED manufacture and supply commercial-grade LED strip lights – which means our products are high quality and built to last, using only premium components and branded LEDs:

  • Brighter LEDs
  • Vibrant and consistent colours
  • Accurate life expectancy
  • Sturdy PCBs
  • Excellent resistor management

Find out more on our ‘commercial-grade LED’ support page.

IP67 Heat-shrink type is required in areas where you will need resistance to water. For example bathrooms, kitchens and exterior. The heatshrink version is waterproof but it cannot be submersed, for example in a pond. The IP67 Heat-shrink is a protective coating over the LED tape, this makes it easy to wipe to clean etc.

For more information, see our support page describing the waterproof LED strip light options we offer.

All the LED strips are cuttable. Each can be cut at various points, either 50mm, 100mm, 150mm or 200mm depending on which wattage version you have. We can either cut the lengths to your specific lengths as required or you can do this yourself. Once cut to length to join this to a transformer or another piece you will need to be capable of soldering, or if not we also supply 2 types of clips. One type is a starter lead clip, which is s clip that joins onto the off cut and has a cable coming out of it. The other clip is a ‘tape to tape clip’, this clip joins 2 pieces together.

For more information, see these links offering advice and support on cutting and soldering your LED tape, or using clip-on connectors to extend your tape’s length.

If you’ve ordered your LED tapes cut to custom lengths from us, with all the starter-leads and flexible leads for corners that your project requires, then you’ve most likely got everything you need already!

But for some installations, the following accessories may prove useful:

Premium-brand customers supplied by InStyle LED


Share this product page!

You may also be interested in the following product(s)

7.5w RGB LED strip

7.5-Watt RGB LED Tape

Our 7.5w RGB LED tape has 30 branded 5050 tri LEDs per metre. so it’s great for feature lighting in clubs, bars and restaurants, and in the home. Use it to light alcoves, ceilings and more.

15w RGB LED strip

15-Watt RGB LED Tape

With twice the output of 7.5w tapes, our 15-watt RGB LED tape is ideal for areas where more brightness is required or where there is a lot of strong ambient lighting. 60 branded 5050 tri-SMDs per metre.

LED light strip

20-Watt RGBW LED Tape

With four colours in each SMD, 20-watt RGBW LED tape mixes light at source for smooth consistent lighting. It will produce up to 1330 lumens per metre when all four colours are at full brightness.

10w white LED lights - 12 volt LED strip lights

10-Watt White LED Tape

With 120 LEDs per metre, each one a branded 3528 SMD, our 10-watt white LED tape draws 9.6 watts to give up to 720 lumens per metre.

12 Watt RGB + Dual-White LED Tape Customer Reviews