7.5 Watt RGB LED Tape

5050 SMD, 30 LEDs Per Metre
Commercial Grade

Availability: In Stock for next day delivery

Our 7.5w RGB LED tape is a flexible LED strip light with a huge range of uses and applications. With 30 branded 5050 tri LEDs per metre, this colour-changing tape draws 7.2w and has 50,000 hours of continuous-use life. When linked to one of our controllers, each tri LED will mix red, green and blue shades – allowing you to programme the colour you need, producing a smooth effect when shone against any surface.

InStyle’s RGB LEDs boast a diffused SMD, which offers superior colour mixing. You can also mix to white, if required. Our 7.5w LED tape is great for feature lighting in clubs, bars and restaurants, and in the home. Use it to light alcoves, ceilings, and much more.

We offer two types of 7.5 watt colour changing LED tape:

  • 12v tape, available in 5m reels as standard with cut points every 100mm. (Also available certified to IP67 standard – which means it can be used in locations prone to moisture – like bathrooms – or even externally.)
  • 24v tape, available in 10m reels as standard with cut points every 166mm.

At InStyle, we can pre-cut and solder either type to the lengths required for your project, no matter how large or small.

InStyle LED supplies commercial grade LED tape using premium components, built to last and with consistent colour batching.  We can also offer you a variety of options to control your colour-changing LED tape – from wireless remote controls to DMX receivers and wall controllers. Please visit our controller page for more details.

  • Commercial Grade LED Tape
  • High Quality Branded LED Chip
  • Thick 2oz PCB board for maximum heat dispersion
  • High grade, long lasting resistors to stop LED chip damage
  • Premium white coating for  protection of the PCB board and to stop short circuiting
  • Smooth linear effect
  • IP65 splashproof & IP67 waterproof available
  • Product Codes:
    RGB-75-12 (12-volt) / RGB-75-12-IP (12-volt Splashproof)
    RGB-75-24 (24-volt)
Product7.5 Watt RGB LED tape
LED Wattage:7.2 watts per metre
Voltage:12 or 24 volts
Colours:Any colour can be created
IP RatingNo coating or
IP65/IP67 heatshrink
LED Chip5050 SMD
LED Life70,000 Hours
No. of LEDs:30 LEDs per Metre
Lumens:On White = 540lm
Beam Angle:120 degrees
Cut Points:100mm (12v), 166mm (24v)
Reel Lengths5 Metres (12v), 10 Metres (24v)
Tape width:10mm
Tape Height3mm

Fully compatible with these LED controllers

RGB Multizone WIFI Controller

Single-Zone RGB Wireless Wall Controller

4-Zone RGB Wireless Controller

single-zone RGB remote control

RGB rotary wall controller

Detachable LED wall control

Product Spec Downloads




Yes you can mix the colours to get a white or warm white colour.

InStyle LED manufacture and supply commercial-grade LED strip lights – which means our products are high quality and built to last, using only premium components and branded LEDs:

  • Brighter LEDs
  • Vibrant and consistent colours
  • Accurate life expectancy
  • Sturdy PCBs
  • Excellent resistor management

Find out more on our ‘commercial-grade LED’ support page.

RGB Tape and the controllers are sold separately, if you purchase RGB Tape with a wireless controller we can set them up and make sure they are working together so you can just install the tape.

For more information, see our support page on RGB and RGBW LED controllers.

RGB stands for Red, Green and Blue. These colours are used in the RGB tape which helps create the millions of different colour combinations that can be output using this tape.

InStyle also offers RGBW tape, which has an additional white LED chip – giving you perfect white light, and the option to mix with the other three primary colours creating a range of pastel shades.

LED strips are designed to be very flexible. Their PCBs (printed circuit boards) are so robust that many LED tape products can be bent up to 90 degrees with no difficulty.

Be aware that higher-power LED strips are less flexible than lower-power ones. This is because the LED modules are placed closer together on high-power strips, and require wider PCBs (for more heat dispersal).

For more info and examples, check out our support page.

To work out what transformer you require this is quite simple. You take the amount of LED tape you have in metres and x this by the wattage of the LED tape you have, again per metre.

For example 10.5m of 7.2w LED tape: 10.5 x 7.2w = 75.6w Therefore you would require a 100w transformer.

For more information, see our support page on LED power supplies and their output.

For this type of LED tape you will require just a transformer to get this working. You connect the 2 core starter lead coming out of one end. This is then wired to the transformer, red wire goes to + and the black wire is wired to -. The 2 core cable can be extended as required for you to mount the transformer as far away as required.

For more information, choose one of these links for support and advice on how to install either simple or larger LED tape projects.

Deciding on which wattage you require is all down to what kind of application you are fitting the LED tape in.

The 5w and 10w is ideal to be used as feature lighting. Lighting to highlight areas, as a secondary lighting. Ideal for covings, drop down ceilings signage etc. to give a smooth halo effect. The 10w would be preferred to the 5w for these applications if there is a high amount of ambient lighting.

The 15w and 20w is ideal to be used as general lighting or as feature lighting for areas larger than covings etc. For example washing down front bars / back bars / under kitchen cabinet lighting as ‘working light’

For more information, see our support page discussing how bright your LED tape needs to be.

IP67 Heat-shrink type is required in areas where you will need resistance to water. For example bathrooms, kitchens and exterior. The heatshrink version is waterproof but it cannot be submersed, for example in a pond. The IP67 Heat-shrink is a protective coating over the LED tape, this makes it easy to wipe to clean etc.

For more information, see our support page describing the waterproof LED strip light options we offer.

All the LED strips are cuttable. Each can be cut at various points, either 50mm,100mm,150mm or 200mm depending on whitch wattage version you have. We can either cut the lengths to your specific lengths as required or you can do this yourself. Once cut to length to join this to a transformer or another piece you will need to be capable of soldering, or if not we also supply 2 types of clips. One type is a starter lead clip, which is s clip that joins onto the off cut and has a cable coming out of it. The other clip is a ‘tape to tape clip’, this clip joins 2 pieces together.

For more information, see these links offering advice and support on cutting and soldering your LED tape, or using clip-on connectors to extend your tape’s length.

If you’ve ordered your LED tapes cut to custom lengths from us, with all the starter-leads and flexible leads for corners that your project requires, then you’ve most likely got everything you need already!

But for some installations, the following accessories may prove useful:

Premium-brand customers supplied by InStyle LED


Share this product page!

You may also be interested in the following product(s)

LED light strip

10-Watt RGBW LED Tape

Outputting up to 665 lumens per metre of LED tape, these 10-watt RGBW LED strip lights produce an ideal level of illumination for highlights and other decorative lighting applications.

15w RGB LED strip

15-Watt RGB LED Tape

With twice the output of 7.5w tapes, our 15-watt RGB LED tape is ideal for areas where more brightness is required or where there is a lot of strong ambient lighting. 60 branded 5050 tri-SMDs per metre.

LED light strip

20-Watt RGBW LED Tape

With four colours in each SMD, 20-watt RGBW LED tape mixes light at source for smooth consistent lighting. It will produce up to 1330 lumens per metre when all four colours are at full brightness.

10w white LED lights - 12 volt LED strip lights

10-Watt White LED Tape

With 120 LEDs per metre, each one a branded 3528 SMD, our 10-watt white LED tape draws 9.6 watts to give up to 720 lumens per metre.

7.5 Watt RGB LED Tape Customer Reviews

Submit your review

Create your own review

7.5-watt RGB LED strip lights by InStyle
Average rating:  
 3 reviews
by Glen Maloy on 7.5-watt RGB LED strip lights by InStyle
Alot brighter than I expected!

I have used this LED tape in my bar to backlight some drinks bottles. The area is quite dark so the LED tape works really well, a lot better than I thought. The light 'spills' through the bottles up the wall and really adds a nice feature. Great product and worked well with the RGB wireless remote.

by Jamie Mitchell on 7.5-watt RGB LED strip lights by InStyle

I used the RGB LED Tape in my living room. I used 18m in total and the wireless controller system. The effect looks stunning and everyone comments on how well they look. I had a lot help from John and would certainly use InStyle again

by Dan Chambers on 7.5-watt RGB LED strip lights by InStyle
Highest quality on the market

When I originally got a quote from InStyle LED it was clear the cost was quite a bit more compared to other companies on the market. However after using several different brands of RGB LED Tape and then using the InStyle RGB LED Tape it was very clear why. So far I have used the InStyle product on 4 installs and have not had a single problem. I am still having problems with the other brands which I have been replacing with the InStyle RGB Tape.