Call Us Today! 0116 2799083 | Next Day Delivery on Orders Before 4pm|Sales@InStyleLED.co.uk
LEDs for handrails and bannisters2018-05-08T11:03:01+00:00

LED tapes can be used to bring feature-lighting and colour to handrails and bannisters. They can be installed both indoors and out.

LEDs on bannister above glass guard

Fitting strip lights to handrails and guards can be less straightforward than many other LED projects.

To produce professional, attractive results will require some planning and preparation. This guide is intended to help!

20-watt RGBW LEDs on the underside of a handrailm reflecting on glass guard panel

Recessing Extrusions:

Housing your handrail LEDs in extrusions (aka LED profiles) will typically produce the best effect. An LED extrusion comes with a frosted cover, which will diffuse the LED strip’s light and eliminate any appearance of ‘dotting’. The aluminium housing will give your lights a more complete, ‘finished’ look, and protect the LEDs from being brushed or touched.

Ideally, the LED extrusion should be fitted in a groove or recess, rather than stood proud on the handrail’s surface.

Recessed groove for a handrail LED fitting

It should be possible to get your handrail supplied with the groove already in place; if not, then you’ll need to rout it yourself.

(Routing is a challenging task, not recommended for the beginner!)

Choose from these LED extrusion profiles to create the effect you want:

Tape Lengths & Voltage Drop:

LED tape lengths longer than 6 metres may suffer from voltage drop, which can cause uneven brightness/dimming towards the end of the run. But it’s quite easy to fit an LED tape run longer than 6m, as long as you plan ahead.

There are two approaches you can take to avoid voltage drop:

White LED tape – 10m loop

-or-


Deep Surface

  • Deep Surface Extrusion

Thin Surface

  • Thin surface extrusion for LED tapes

Deep Recess

  • Deep Recessed Extrusion

Shallow Rcss

  • Shallow Recessed Extrusion

Some installers prefer to rout a deeper groove in the handrail and fit the bare LED tape into it, without an extrusion. This arrangement will let you see the LEDs’ light, but keep the strip lights themselves from view. A depth of, say, 10mm will be enough to create a good effect.


White LED strip lights:

The output / brightness your handrail needs will depend on the location and surrounding illumination. As with most feature-lighting projects, we recommend either 5W or 10W LED tapes for a typical handrail installation using white LEDs.

warm white LEDs lighting the handrail of this decking at night

5-watt LED strips will give the rail a subtle glow…

5-watt white LED strip lights

10-watt LED strips will be bright enough to light up part of the staircase, pathway or other location…

10w white LED lights - 12 volt LED strip lights


For an exterior project, your external transformer(s) should be installed in a protected box (IP-rated), or fitted in an interior location and connected to the starter-lead points of your outdoor strip-lights using 1.5mm cabling. (These cables can run up to 20m away from the transformer with no loss of power.)

You may want to add a remote controller to manage your handrail’s dimming and set the brightness:

Easy RF LED Dimmer

Wireless dimmer/controller for white & single-colour LEDs

For RGB LED projects, InStyle’s 7.5W LED tapes will be ideal for most handrail feature lights…

7.5w RGB LED strip

If you’re using four-chip RGBW LEDs, then our 10W strips will give a level of feature-lighting that’s right for most handrails…

RGBW LED strip comparison


In locations with a lot of ambient illumination, or for bigger, more expensive installations intended to flood the area with light, we recommend choosing either:


To control your RGB/RGBW LEDs, a wireless remote control is usually the preferred option. You’ll probably want to fit the corresponding LED receiver in an interior location (wireless range is up to around 20m), or in an IP-rated protective box (like the power-supply discussed earlier).

…Or you could use a wall controller, perhaps with the facility to manage multiple lighting zones if this is part of a larger installation.

RGB LED remote
RGBW remote control for LEDs - supplied with compatible receiver


These recommendations apply to InStyle’s commercial-grade Epistar-branded LED strip lights. For lower-grade strip lights from elsewhere, adjust accordingly.